![]() The next steps are determined by whether or not you have a DNS server that you can control and configure. You can skip this section and go to Activate Printers. If your network has a single subnet, Presto is preconfigured. The above steps are also explained in the following video:Īfter completing this step, the Presto Administrator will launch. On the new host, after Presto installation, select 'Yes', you want to connect to Presto running on another machine.Copy the token for the new Host details.For more details on Hosts, see Hosts in Presto Administration. For more details on accessing the Primary Presto instance on both the Host system and remotely through a browser, see Accessing Presto in Presto Administration. You will need to access the Primary Presto instance and generate a token to allow the extender to communicate with the Primary instance. For more information on post-installation management of Extenders, see Hosts in Presto Administration.An Extender can only be installed while a Primary instance of Presto is running. ![]() Configure a Presto ExtenderĪ Presto Extender, also referred to as a 'Host', should be installed on all additional print servers to enable the discovery of installed printers. Note: If you have entered Web Proxy information but still have problems connecting during the licensing procedure, see Network Requirements in Presto Troubleshooting for comprehensive information about ports and URL whitelisting.Īfter completing this step, the Presto Administrator will launch. If your site uses web proxy server software, click 'Proxy' and enter the required information into the dialog box. If you are unable to find your license key, contact Collobos Support. If you already have a licenseĮnter your license key and Organization Name. Note: If the submitted email address has already been verified, installation will proceed immediately.Īfter completing this step, the Presto Administrator will launch. Once you have verified your email address, your Presto Trial will be provisioned and you will continue. If you do not receive a verification email, or believe that you have supplied the wrong email address, contact Collobos Support You will be asked to supply some initial information after which you will be sent a verification email. The initial step in configuring your Primary is activating your Presto license. If this is an Extender instance, select 'Extender' and go to Configure a Presto Extender.If this is a Primary instance, select 'Primary' and go to Configure a Primary Instance of Presto.Once the installation has completed, you will be asked how you want to set up the Presto Service. After installation has completed, click Finish.Accept the licensing agreement and proceed with installation.Note: Both the Primary and the Extenders require the same install executable Installation procedure for a Primary or Extender instance of Presto Install Presto Extender on the DNS server to discover printers (see below) - ensure that the Presto Service is run as Domain Administrator.Install Presto Server on a new VM or alternate host.If your print server is also your DNS server or Domain Controller there is an easy workaround: Note: You should not install Presto Server on a DNS server/Domain Controller.You can find more detailed information in our Deployment Configuration Guide. Presto supports complex network deployments.If a new VM is not possible, Presto should be installed on any computer or server that has printers installed.We recommend spinning up a new VM exclusively for the Presto Primary Server, using Presto extenders as required.Installation guidelines for a Primary instance of Presto We recommend disabling any anti-virus software that may be running during the installation of Presto. You will need a single Presto Primary instance and possibly one or more Extenders, depending on the specifics of your network. The first step in setting up Presto is to enable printer discovery by installing and licensing Presto as needed on your network. System Requirements Minimum Hardware Requirements Your purchase of the Presto 3 license entitles you to free upgrades to all Presto 3.x versions. If you are running an earlier version of Presto 2, we encourage you to upgrade as soon as possible. Note: The contents of this article are specific to Presto Server version 3.0 and later. A comprehensive guide to setting up Presto, from download to configuration.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |